Showing posts with label clone a willy. Show all posts
Showing posts with label clone a willy. Show all posts
Friday, 31 August 2012
Tuesday, 21 August 2012
Clone A Willy Review
Clone A Willy kit – light tone
- a moulding tube - designed to accomodate most penis sizes
- moulding gel - algae-based gel is specifically timed to garantee a perfect mould of an erect penis
- moulding powder
.jpeg)
- liquid rubber and liquid skin - mixed together to create every intricate detail of your clone
- multi speed vibrator unit
- thermomitor
- wooden spatular
- full Clone A Willy instructions
Setting up this kit ready was simple and easy to do the
plastic tube is cut down to size and you cover the cut end with tape to ensure
you have no sharp edges although I found this wasn’t really necessary I did so
as I was determined to follow the instructions to the letter
Having helped my husband reach the appropriate aroused state
I got to work with the mould itself, you use 425ml of water at the temp of 37 degrees celsius which is the equvalant to 98 degrees fahrenheit and mix that in with the white moulding powder, you must mix this together
quickly and it looks a lot like lumpy porridge which is what it should look
like, within the two minutes time limit you must mix the mixture and submerge
the erect penis inside.
This is where the fun starts having set everything out extra
carefully and my timer on ready I got started and in my eagerness I totally
forgot to start the timer, cursing and rushing like a loon worried I would mess
up I mixed like my life depended on it as my husband laughed his arse off
rather enjoying the show. Then i pushed my hubby’s cock inside sending moulding
mixture all down his leg and on to the floor, at this point we were both in
hysterics, realising his penis was touching the side of the plastic tube I
did as instructed and turned the tube which sorted the issue. And it soon
became apparent I had no need to panic the way I did as the Clone A Willy kit was work
exactly as it should have
.jpeg)
My husband informed me the feel of the mixture was not
unpleasant but was cool and cooled even more so very quickly which sent his
semi erection fully flaccid despite the fact I was knelt before him completely
naked
Having waited the two minutes needed for the moulding
mixture to firm we tested the end and sure enough it felt like squishy rubber, a
gentle pull, holding the open end of the
mould with my fingers and hubby was free, the removal was pain free and caused
no discomfort at all
Now for the clean-up which was remarkably easy I was
expecting the clean-up to be quite tricky but in truth it could not of been
easier, the moulding mixture peeled right off and even on the hairy areas of his
legs this was completely painless and again the mixture I spilt on the floor
also peeled straight off as did the excess mixture in my mixing bowl.
As instructed we left the mould for a couple of hours and
then tipped out the accumulated water from inside the mould which is completely
normal and set to work mixing together the two pots of rubber mix one is the
liquid rubber a clear thick mixture with a similar consistency to honey, the
other is the light skin toned liquid skin mixture which is slightly runnier.
Having mixed them together vigorously for the allotted two minutes we tipped it
inside the mould leaving space to insert the vibrator provided.
Before inserting the viberator unit you need to make sure you have
something to keep it in place which you do so using card, cut out a piece of
card larger than the tube and snip an "x" into the centre large enough to hold
the viberator snuggly at the screw top end, this is to ensure you do not submerge it
too far and impair battery change to the vibrator. This I done before filling
the mould with the rubber mixture but as it only takes a minute you can do this
after if you forget as long as you do not leave it to long
Once you have poured the liquid skin mixture into the mould
you insert the vibrator inside it, this is a tad difficult to judge if you have
inserted the vibrator into the mould straight but I gave it my best guess and the
card sits onto of the plastic tube holding it in place nicely
Now for the wait you must leave the mixture to cure (harden)
for 24 hours, I would suggest placing the mould somewhere safe and out of the
way to make sure it is not knocked over
Once the 24 hours is up you must check to ensure that the
rubber mixture has indeed cured and then you can gently remove the finished
clone from the mould this was easily done with a gentle twist and pull and it
popped right out
As we expected the mould was an almost perfect replica of my
husbands flaccid penis but this is something we both actually really loved the
detail on the clone is amazing and the liquid skin feels great
My husband and I were both very impressed by the detail captured on the clone and the product worked remarkably well as expected from any products
from Clone A Willy `
The Clone A Willy products are a great way for couples to
bond and have fun and my husband and I enjoyed the experience immensely and are
already planning more clones in the immediate future
Although we didn’t manage to capture my husband’s erect
penis this was no fault of the Clone A Willy product and I can not stress this
enough the product work exactly as it should, it was more our inability to take
it to seriously we had far to much fun with the product, we had plenty of
giggles and genuinely had a lot of enjoyment from it which is something you
want from a product of this nature and
the best part of all is we now have a perfect clone to keep and play with for
many years to come
We would both highly recommend this product as I have
already mentioned it is a great way for couples to bond and the end result is a
completely unique and personal product of the highest quality that you will
love and cherish for many years
To get our hands one one of these amazing kits or one of the other great products from Clone A Willy visit there sit HERE
Subscribe to:
Posts (Atom)